AdrenaLinn Sync

* RTAS plug-in format (for Pro Tools) is added.
* In Logic 9, sometimes Logic would crash when AdrenaLinn Sync v2 was loaded or when its panel was opened. This is fixed.
* If a preset was selected and edited, then ASync2's settings were saved as a preset from the host DAW (not from within AdrenaLinn Sync v2) and later reloaded, the AdrenaLinn Sync v2 panel would show the original unedited settings. This has been fixed.
* If ASync2's settings were saved as a preset with a new name from the host DAW, then later reloaded, the Preset Name field in ASync2's Preset Name display would not show the name of the saved preset. Unfortunately it is impossible for a plug-in to receive the loaded preset name from the host DAW, so now whenever a host-saved preset is loaded, the Preset Name display on ASync2's panel shows "".
* The pulsing LED in the LFO section would be off for negative output values of the LFO. Now, the LED is on for full positive output, half brightness for 0 output and off for full negative output.
* If the Phasor filter type is used with high Resonance settings and the input signal contains a large amount of midrange, the filter could self-oscillate, corrected only by temporarily reducing Resonance to 0. This has been fixed.

* In Logic, the preset number shown in AdrenaLinn Sync v2 was one less than that shown in Logic's preset name display. This is because AdrenaLinn Sync v2 interprets Logic's preset numbers 0-127 as 1-128. To workaround this, Logic's preset name display no longer shows AdrenaLinn Sync v2's preset number but rather only its preset name. This has the added benefit that Logic now shows 4 more characters (31 instead of 27) of the preset name.
* In Logic, if you press Logic's PRESET INCREMENT or PRESET DECREMENT buttons to change AdrenaLinn Sync v2's presets, the wrong preset would often be selected in AdrenaLinn Sync v2, sometimes one higher and sometimes one lower. This has been fixed.
* In Logic 9, if one of AdrenaLinn Sync v2's preset names contained a slash character ("/"), then only characters after the slash would be displayed in Logic's preset name field, due to a bug in Logic. To workaround the bug, we removed all slashes from AdrenaLinn Sync v2's preset names. After upgrading from AdrenaLinn Sync v2.0.0 to v2.0.1, to replace your existing presets with the new presets containing the non-slash names (which will also delete any presets you've created), delete your existing presets file before starting AdrenaLinn Sync v2.0.1:
Macintosh HD/Users/(your username)/Music/AdrenaLinn Sync v2/Sessions/async_presets
* In Logic, if Pre-Roll was used, causing a negative bar number to be sent to AdrenaLinn Sync v2, in some cases Logic would crash. This has been fixed.
* If AdrenaLinn Sync v2 was opened within Iced Audio's AudioFinder, AudioFinder would crash. This has been fixed.

* New in V2: Warm, punchy and faithful emulations of analog lowpass, bandpass and hipass filters, as well as superb analog
* New in V2: 100 new presets, optimized for the new V2 filters, and now able to be selected or saved from the plug-in's panel. 28 empty preset slots are also included for saving your own presets.
sweeping through the spectrum and emphasizing only notes in the D Major scale as it moves.
* New is V2: Stereo Beat-Synced Delay up to 32 Seconds / 8 Bars -- Play 8 bars of accompaniment, then listen to it while playing 8 bars of solo, then listen to that solo while adding another 8 bars of chords, and so on. With Feedback at full, it loops indefinitely.
* New in V2: Limiter improved for faster attack and greater transparency -- Levels out resonant filter peaks and also adds sustain, providing longer chords and notes for the rhythmic effects to chop and slice.
* New in V2: Unlike the original version, version 2 no longer uses Cycling 74's Pluggo technology. This means that unlike the original AdrenaLinn Sync release, version 2 works fine in Cubase and also in Live 8 when Max For Live is installed.
* And lots more little improvements.

* Fixed bug: If multiple instances of AdrenaLinn Sync were open in the same project, select a preset or editing a parameter in one instance would affect the other instances